Go Back   Ducati 1299 Forum > Ducati Panigale Forum > Ducati 1199

Ducati 1199 Ducati 1199 Forum - Ducati 1199 Panigale Superbike Motorcycle Forum


Thanks Tree2Thanks
  • 1 Post By tteitei
  • 1 Post By tadashi
Reply
 
LinkBack Thread Tools Display Modes
Old Jul 28th 2017, 08:30 AM   #1
Member
 
Joined: Dec 2016
From: Singapore

Posts: 74
Thanks: 18

I Ride: 1199s
Tuneboy cruise, QS, blipper and iPhone app lessons learnt

Hi Guys,

I have installed the tuneboy tune (V6), cruise, quick shifter and modified Aux switch for the cruise control (found on the 1299) on my 1199S. I also have the iPhone app working. Here are some answers to some questions I've noticed on various tuneboy threads;

Aux button use for cruise control
This is the +/- button found standard on the 1299 but absent on the 1199. This needs to be modified for use with the cruise control by adding a resistor and some wiring changes and then needs to be connected to the front O2 sensor. It will not work as standard on the 1299 as far as I know (could be wrong about this). I purchased this switch (Domino brand) from Wayne which he modified for me so it came with the right wiring and connector. Here is an excerpt of an email from Wayne explaining the modification required;

The pins on the Ducati O2 sensor plug are numbered 1,2,3,4
1 = signal.
2 = ground
3 = 12v

My adapter loom has a 10k and 2.4k resistor (from JayCar electronics).
The buttons from Domino have brown, green and white wires.
Brown is common to both buttons, this goes to pin 1 (signal)
White goes to pin 2 (ground), pin 2 is also connected to one side of the 2.4k resistor.
green connects to the other side of the 2.4k resistor, this side or the resistor also connects to one side of the 10k resistor.
The other side of the 10k resistor connects to pin 3 (12v)

The resistors act as a voltage divider so the point between the two resistors is about 2.7v
When the nudge up button is pushed it connects the signal wire to the 2.7v, when the nudge down is pushed it connects the signal to ground.

iPhone app
You will need to provide the UDID number of your phone to Wayne as his app has not yet been uploaded to the app store so he is manually enabling test users. You need to connect your iPhone to your PC and get the UDID number. Also I found that to get the app to communicate with the ECU, the Innovate device needs to be connected and the bike switched on before you see any response from the app itself. This threw me initially as I expected some connection information when I selected the tuneboy wifi network and I did not see the Wifi symbol showing at the top status line on the phone, it still showed the LTE signal status even though its connected via WiFi so I thought it wasn't connecting properly.

Quickshifter/blipper
Appear to be working correctly but could be improved with some tweaking. Sometimes the upshifts in the lower gears at mid revs is a bit jerky but similar to what I was experiencing with the standard QS. Sometimes its smooth. The blipper is working well and I am finding the downshift pressure a little hard but will try readjusting this in the software. Also it is not necessary to re-download the tune map again when enabling the QS or adjusting the Cruise options. You just need to go to the config page (after the mitsubishi program has read the map from the ECU), make the selections and exit the page. The default setting Wayne advised I set up the QS initially at were;

QS kill time - 5mm from the left
QS pressure - kill just to the right of the mark shown on the slider
Blip pressure - blip pressure slide just to the left of the mark

I will try increasing the QS kill time to see if it will reduce the jerkiness in the lower gears but I'm not sure this is correct (waiting on a response from Wayne).

Cruise control options
I selected the option 'nudge buttons with resume function' which is found on the config page of the mitsubishi program. This option enables the down button on the Aux switch to act as a resume feature, similar to a car cruise control. Also note the +ve button now replaces the cruise control set function that the start button used to perform. Pressing the start button only enables cruise control when this option is selected.

Regards,

Yoshi
Thanks from mordor

Last edited by tteitei; Jul 28th 2017 at 08:32 AM. Reason: correction
tteitei is offline  
 
Old Jul 28th 2017, 04:10 PM   #2
Senior Member
 
tadashi's Avatar
 
Joined: Jun 2015
From: Orange County, CA

Posts: 419
Thanks: 159

Originally Posted by tteitei View Post
Hi Guys,

I have installed the tuneboy tune (V6), cruise, quick shifter and modified Aux switch for the cruise control (found on the 1299) on my 1199S. I also have the iPhone app working. Here are some answers to some questions I've noticed on various tuneboy threads;

Aux button use for cruise control
This is the +/- button found standard on the 1299 but absent on the 1199. This needs to be modified for use with the cruise control by adding a resistor and some wiring changes and then needs to be connected to the front O2 sensor. It will not work as standard on the 1299 as far as I know (could be wrong about this). I purchased this switch (Domino brand) from Wayne which he modified for me so it came with the right wiring and connector. Here is an excerpt of an email from Wayne explaining the modification required;

The pins on the Ducati O2 sensor plug are numbered 1,2,3,4
1 = signal.
2 = ground
3 = 12v

My adapter loom has a 10k and 2.4k resistor (from JayCar electronics).
The buttons from Domino have brown, green and white wires.
Brown is common to both buttons, this goes to pin 1 (signal)
White goes to pin 2 (ground), pin 2 is also connected to one side of the 2.4k resistor.
green connects to the other side of the 2.4k resistor, this side or the resistor also connects to one side of the 10k resistor.
The other side of the 10k resistor connects to pin 3 (12v)

The resistors act as a voltage divider so the point between the two resistors is about 2.7v
When the nudge up button is pushed it connects the signal wire to the 2.7v, when the nudge down is pushed it connects the signal to ground.

iPhone app
You will need to provide the UDID number of your phone to Wayne as his app has not yet been uploaded to the app store so he is manually enabling test users. You need to connect your iPhone to your PC and get the UDID number. Also I found that to get the app to communicate with the ECU, the Innovate device needs to be connected and the bike switched on before you see any response from the app itself. This threw me initially as I expected some connection information when I selected the tuneboy wifi network and I did not see the Wifi symbol showing at the top status line on the phone, it still showed the LTE signal status even though its connected via WiFi so I thought it wasn't connecting properly.

Quickshifter/blipper
Appear to be working correctly but could be improved with some tweaking. Sometimes the upshifts in the lower gears at mid revs is a bit jerky but similar to what I was experiencing with the standard QS. Sometimes its smooth. The blipper is working well and I am finding the downshift pressure a little hard but will try readjusting this in the software. Also it is not necessary to re-download the tune map again when enabling the QS or adjusting the Cruise options. You just need to go to the config page (after the mitsubishi program has read the map from the ECU), make the selections and exit the page. The default setting Wayne advised I set up the QS initially at were;

QS kill time - 5mm from the left
QS pressure - kill just to the right of the mark shown on the slider
Blip pressure - blip pressure slide just to the left of the mark

I will try increasing the QS kill time to see if it will reduce the jerkiness in the lower gears but I'm not sure this is correct (waiting on a response from Wayne).

Cruise control options
I selected the option 'nudge buttons with resume function' which is found on the config page of the mitsubishi program. This option enables the down button on the Aux switch to act as a resume feature, similar to a car cruise control. Also note the +ve button now replaces the cruise control set function that the start button used to perform. Pressing the start button only enables cruise control when this option is selected.

Regards,

Yoshi


Nice write up!
Thanks from tteitei
tadashi is online now  
Reply

  Ducati 1299 Forum > Ducati Panigale Forum > Ducati 1199

Tags
app, blipper, cruise, iphone, learnt, lessons, slipper, tuneboy



Thread Tools
Display Modes


Similar Discussions
Thread Thread Starter Forum Replies Last Post
For Sale: Tuneboy Tune + Cruise Control ECU 1199(S/R ) 899 tadashi Classifieds 7 Apr 13th 2017 06:58 PM
Tuneboy cruise control error disabled DQS? bretm Ducati 1199 13 Sep 8th 2015 05:52 PM
Tuneboy cruise control AG6 Ducati 1199 37 Jun 16th 2015 07:02 PM
Tuneboy cruise control and BSD starter switches DynastySS Ducati 1199 11 Feb 2nd 2015 03:01 PM
Tuneboy Cruise Randomly Activated PanigaleS Ducati 1199 4 Dec 30th 2014 08:50 AM


Facebook Twitter Google+ RSS Feed